Interiors · Kitchens

Kitchen cabinet materials: two choices, not one

"What are the cabinets made of?" is really two questions rolled into one, and conflating them causes most of the confusion when comparing quotations:

  1. The board core — what is inside, which decides how the unit survives moisture.
  2. The surface — the outer finish, which decides appearance and cleaning.

They are chosen separately. A high-gloss acrylic door can sit on a moisture-resistant core or an ordinary one. From the outside they look identical; the price differs appreciably; after three years they do not.

Choosing the core

Standard MDF

Use for: wall units and carcasses in dry areas.

Strengths: flat, smooth, accepts any surface, sensible cost.

Weakness: it swells on contact with water, and swelling is permanent. One leak under the sink ruins the base unit.

Moisture-resistant MDF

Use for: all base units, the sink cabinet, units against an external wall.

A point worth clarifying, as it is frequently overstated: moisture-resistant board resists humidity, not standing water. Left sitting in a pool for days it still fails. It buys time to notice a leak; it is not immune to one.

PVC foam board

Use for: the sink cabinet, rental properties, houses left unattended.

Strengths: contains no timber, so it cannot swell and insects cannot attack it.

Weaknesses: softer than MDF, so screws hold less well — hinges and runners under load work loose over time. Heavier, and dearer than moisture-resistant MDF.

Many workshops combine the two: PVC foam for the sink cabinet, moisture-resistant MDF elsewhere. That is sound on both cost and durability.

Solid timber

Use for: doors, face frames and mouldings — rarely for carcasses.

Strengths: real grain, repairable by sanding and refinishing, improves with age.

Weakness: the highest cost, and it moves with the weather if the timber was not properly dried. Warped solid doors are the most common complaint, and the cause is the timber rather than the workmanship.

Choosing the surface

SurfaceAppearanceWeakness
MelamineMatt, woodgrain or plainThinnest layer, edges chip, not repairable
LaminateMatt or textured, substantialDearer than melamine
AcrylicHigh gloss, deep even colourShows fine scratches and fingerprints
Sprayed lacquerAny colour, can follow curvesScratches most easily — but repairable
VeneerReal wood grain on boardThin; heavy sanding goes through it

Melamine or laminate?

The real difference is the thickness of the surface layer. Laminate is several times thicker, so it resists impact and scratching better and the edges chip less. Melamine is cheaper and perfectly adequate for wall units. Look at a cut edge and the difference is visible.

Is acrylic a good choice?

High-gloss acrylic reads as clean and modern, with deep even colour. It suits contemporary kitchens and apartments. Three things to know first:

  • Gloss shows everything — fingerprints, water marks, fine scratches, especially in dark colours.
  • Scratches cannot be repaired in place. Unlike lacquer, a deeply scratched acrylic door is replaced.
  • Edge banding decides its life. Acrylic doors almost always fail from an open edge letting moisture in. Ask what machine and what adhesive the workshop uses.

Suggested combinations

PositionCoreSurface
Sink cabinetPVC foam or moisture-resistant MDFMatching the rest
Other base unitsMoisture-resistant MDFLaminate or acrylic
Wall unitsStandard MDF is sufficientMatching the base units
Units on an external wallMoisture-resistant MDFAs preferred
Curved doors, mouldingsMDFSprayed lacquer

Ironmongery: the line most often overlooked

Hinges, runners, soft-close, corner mechanisms, pull-outs. On a kitchen this can be a substantial share of the value — and it is the easiest line to downgrade, because the buyer never sees it.

It is also what fails first. Doors look the same after ten years; hinges drop and runners stick after two or three.

Ask which manufacturer, whether soft-close is included, and what the warranty covers. Require the manufacturer's name in the contract rather than "imported ironmongery".

How Tropicity works

Tropicity Interior runs its own joinery workshop with CNC router, edge bander and wide-belt sander. Clients see core samples, finish samples and ironmongery before anything is cut, and our quotations state core, surface and ironmongery manufacturer as separate lines.

We also say where not to spend: moisture-resistant board in wall units is usually wasted money, better put into ironmongery.

See standard kitchen dimensions, choosing a worktop, or the interiors page.

Send your kitchen plan for an itemised quotation

Free preliminary estimate

Get our company profile and a budget range within 48 hours

Tell us where your project is and what you plan to build. A Tropicity engineer replies within one working day and arranges a site visit in Ho Chi Minh City and the southern provinces.

  • One contract, one estimate, one point of contact
  • A structural engineer visits your site
  • English-speaking contact; no marketing emails

Why the site address? Planning rules, building density and truck access change the price. Without the address an estimate is only a generic figure.

Please enter your name.
Please enter a valid email.
Please select a project type.
Please enter the project location.

Urgent: call +84 937 989 858

Zalo