Dropped sashes, draughts and leaks: causes and fixes
Few door manufacturers document these faults, because doing so admits that aluminium doors fail too. Clients need to know — which faults are a warranty matter, which come from poor installation, and which need nothing more than one screw turned.
1. A sash that has dropped
Signs: the sash catches on the frame at the lower corner, it has to be lifted to close, the gap is wider at the top than the bottom, the lock no longer meets its keep.
Causes
- The sash is too large for the series. The most common cause and the hardest to put right, because it originates in the choice of system. A sash wider and taller than the series will carry lets the weight of the glass distort the frame over time.
- Too few hinges, or poor ones. A heavy sash on two hinges, or on unbranded hardware, works its fixings loose.
- Inadequate fixing into the structure. Frames fixed into hollow block or into render rather than solid masonry move as a whole.
- Settlement or cracking pulling the frame with it. Here the door is only where a structural problem becomes visible.
What is done
Many hinges carry three-way adjustment — up and down, in and out, side to side. Resetting them takes a fitter 15 to 30 minutes and cures a minor drop. Call the installer rather than turning screws yourself; adjusting the wrong axis makes it worse.
Where the cause is an oversized sash, adjustment is only a reprieve. The real remedy is additional hinges, a redivided sash, or a series that carries the span. See choosing a profile series.
2. Doors that no longer seal
Signs: wind audible through a closed door, daylight visible at the edge, air conditioning struggling, dust coming in.
Causes
- Gaskets hardened or displaced. Rubber gaskets are a wearing part; after a few years they stiffen and lose their spring. The most frequent cause, and the easiest to remedy.
- Multi-point locks not fully engaging. Where the keeps on the frame are misaligned, only some points engage and the sash is not pulled evenly onto the gaskets.
- A dropped sash (see above) opening a gap on one side.
- For sliding doors, some of this is inherent. A slider never seals like a casement. Where a true seal is required, a casement is the right choice from the outset.
3. Water entering through the door
Signs: a pool at the threshold after heavy rain, or damp tracking down the plaster beside the frame.
Causes — and this is where blame is often misplaced
- Blocked drainage slots. Aluminium frames have small slots in the bottom member so that water reaching the frame can escape. Dust, grit and insect debris block them, water backs up and then overflows inwards. A great many "leaking door" callouts are nothing more than blocked slots.
- Perimeter sealant cracked or never fully applied. Sealant has a service life; after a few years it shrinks and splits.
- A sliding threshold with no drainage channel, or one falling the wrong way. This originates in the building work and must be corrected there.
- No canopy where rain strikes directly. No door withstands water thrown at it continuously for ever.
Cracked sealant must be cut out completely before resealing — new sealant will not bond over old.
4. Sliding doors that are noisy or stiff
Cause: mostly grit in the track, which jams the rollers and wears them unevenly. The rest is poor rollers whose bearings have failed, or track damaged during construction.
Vacuuming the tracks regularly is the best prevention. Do not oil the track — oil attracts grit and makes everything worse. Worn rollers are replaced; they are a normal wearing part.
5. Misting inside an insulated unit
Condensation between the two panes that cannot be wiped away means the edge seal of the unit has failed and humid air is entering. It cannot be dried out or cleared; the whole unit is replaced. Within the warranty period this is a material defect and should be covered.
What a warranty should cover
| Symptom | Usually |
|---|---|
| Sash dropping in the first year | Installation or hardware — covered |
| Multi-point lock not engaging | Installation — covered |
| Misted insulated unit | Material defect — covered |
| Water entering via blocked slots | Maintenance — not a defect |
| Gaskets hardened after some years | Wearing part — replace, usually not covered |
| Dirty tracks, worn rollers | Maintenance and wear |
| Water entering with no canopy | Design — needs shelter added |
At contract stage, establish how long the warranty runs and what it covers: profile, ironmongery and installation are three separate things and often carry different periods. See how to read a door quotation.
Maintenance that avoids the callout
- Once a year, before the rains: clear the drainage slots in the bottom frame and the sliding tracks.
- Vacuum sliding tracks every few months. No oil.
- Inspect perimeter sealant annually; cut out and reseal at the first sign of splitting.
- Clean aluminium with water and a soft cloth. No harsh chemicals or abrasives — a damaged coating is where corrosion starts.
- Report unusual noise early. A slight drop is 20 minutes of adjustment; left a year, the hinges have worn unevenly and need replacing.
How Tropicity handles it
Because we run our own aluminium and glass workshop, repairs and hardware replacements are carried out directly rather than through a dealer. For doors we supplied, we keep a record of the series and ironmongery used on each building, so replacements match.
We will survey and repair doors supplied by others — with one caveat stated in advance: where the fault is a sash oversized for its series, the real remedy is remaking rather than adjusting.
See the Tropicity Windows page or contact us.