Aluminium and glass

How aluminium door prices are calculated, and why quotations differ so widely

Ask several suppliers what aluminium and glass doors cost per square metre and the figures can differ by a factor of two. This article does not add another figure. It explains what creates that spread, so a quotation can be read for what it actually contains.

Why no rate is published here: imported aluminium moves with each batch and with exchange rates, glass varies by type and thickness, and ironmongery differs enormously between manufacturers. A figure printed on a website is accurate for a few weeks and then misleading — and quoting below the real cost is a familiar way to prompt a phone call. Send dimensions and we will quote the actual job.

How the measure works

Most suppliers price by square metre of door face, width times height. Three things are regularly misunderstood:

  • There is usually a minimum area per opening. A small window is charged at that minimum, commonly 1 m² or 1.5 m², because cutting a small unit costs nearly as much labour as a large one.
  • The smaller the unit, the higher the rate per square metre, since frame and ironmongery barely change while the glass area falls.
  • Each door type has its own rate. There is no single rate for a whole house: casements, sliders, folding doors and fixed glazing differ substantially.

Seven sources of difference

1. Origin of the profile

Imported Guangdong profile, Guangxi profile and domestically extruded profile are three distinct price levels for doors that look identical. This is the largest single cause of difference, and the one most often left vague. See how to identify genuine Xingfa.

2. Wall thickness

Moving from roughly 1.4 mm to 2 mm is a real difference in material, so it is a real difference in price. A quotation that omits the thickness cannot be compared.

3. Series and opening type

A sliding system and a casement system use different quantities of aluminium, different hardware and different fabrication time. See the profile series explained.

4. Glass

The second largest variable after aluminium, and the easiest to substitute:

  • Float versus toughened — different price, and different behaviour when broken
  • Toughened 8 mm versus 10 mm
  • Insulated units (two panes with a sealed cavity) — considerably more, but markedly better for heat and noise
  • Tinted, obscured and reflective glass each carry their own rate

Two quotations 30% apart may differ only in that one is toughened 8 mm and the other is float glass.

5. Ironmongery

Hinges, locks, multi-point mechanisms, handles, sliding rollers. A buyer can barely inspect any of it once installed, which makes it the easiest place to reduce a price. It is also what determines whether a door still works in three years — profile rarely fails; hinges, rollers and gaskets do.

6. Associated work frequently omitted

  • Removing and disposing of existing doors
  • Sealing and making good the surrounding plaster after installation
  • Cover trims and finishing beads
  • Insect screens and safety bars
  • Carrying to upper floors where there is no lift
  • Scaffolding or craneage for large units

7. Special fabrication

Arched heads, heavily divided lights, louvre panels, louvre-below-glass-above units and decorative bars within insulated glass each add labour and hardware. Arched work requires bending equipment and higher material wastage, so it costs appreciably more than straight work of the same area.

Reading two quotations side by side

  1. Aluminium: line and origin stated specifically
  2. Wall thickness in millimetres
  3. Profile series for each door type
  4. Glass: type, thickness, toughened or insulated
  5. Ironmongery: manufacturer named
  6. Minimum charged area per opening
  7. An explicit list of exclusions
  8. Warranty: how long, and on what — profile, ironmongery and installation are three separate things
A useful rule: the cheapest quotation is often the shortest one, and frequently the most expensive by completion. Lines left out do not disappear; they arrive later.

How Tropicity quotes

We separate four lines — aluminium (line and origin stated), glass, ironmongery (manufacturer named), and fabrication and installation — with an explicit list of exclusions. Comparing line by line shows where a difference sits, rather than comparing two totals.

Tropicity runs its own aluminium and glass workshop, with no intermediary, so the fabrication line is the workshop's actual cost.

See the Tropicity Windows page or the product catalogues.

Send your dimensions for an itemised quotation

Free preliminary estimate

Get our company profile and a budget range within 48 hours

Tell us where your project is and what you plan to build. A Tropicity engineer replies within one working day and arranges a site visit in Ho Chi Minh City and the southern provinces.

  • One contract, one estimate, one point of contact
  • A structural engineer visits your site
  • English-speaking contact; no marketing emails

Why the site address? Planning rules, building density and truck access change the price. Without the address an estimate is only a generic figure.

Please enter your name.
Please enter a valid email.
Please select a project type.
Please enter the project location.

Urgent: call +84 937 989 858

Zalo