Building a factory in Vietnam: from land to production
A factory differs from a house in one basic respect: it is a production tool, not somewhere to live. Every decision comes back to one question — how do machines and goods move through it. This article follows the real sequence, with the points where budgets tend to overrun.
1. Choosing the site
The decision that matters most and can be corrected least. Four checks before any deposit:
- Permitted land use on the title. The land must allow production facilities. Agricultural land requires a change of use, which is not always granted.
- Whether your industry may operate at that location. Zoning differs, and some activities are restricted by area.
- Electrical capacity and water supply. Upgrading a substation is expensive and slow, and many buyers discover the limit only after purchase.
- Access. Whether a container lorry can turn, and what the bridges on the approach will carry. Factories that lorries cannot reach have been built before.
2. Permits and legal documentation
So: ask the management board of the industrial park and the provincial Department of Construction directly rather than relying on articles online — this one included.
What can be said with confidence:
- Inside an industrial park and outside one are different situations, with different procedures, different filing authorities and different conditions.
- An industrial park and an industrial cluster are also different things — frequently confused, and exemptions written for the former do not automatically apply to the latter.
- Exempt does not mean nothing to do. Notice of the commencement date, with the design documents, is normally still required.
- Other approvals sit alongside the construction permit: environmental documentation, fire-safety design approval, and utility connections. Fire safety is the one most often left late, and correcting it after construction is costly.
3. Ground investigation
Boreholes establish what the soil will carry. For a factory this governs two expensive things: the column foundations and the floor slab.
Do not skip it to save money. A floor that settles unevenly after a year takes machines out of level and cracks the slab — and repairs mean stopping production.
4. Design — where the real cost is set
Span, and why it drives the price
Span is the distance between column lines — the width of uninterrupted space inside. A 20-metre span means 20 metres with no column in between.
The larger the span, the heavier the rafters and beams, so steelwork cost rises steeply with span. But a short span puts columns in the path of forklifts and constrains the production line.
This is a calculation, not a preference: draw the process flow and the forklift routes first, then fix the span. Done the other way round, you discover a column in a gangway after it is built.
Other parameters to settle early
- Clear height — from racking height, forklift lift height and space for services.
- Floor loading — where heavy machines stand, and the maximum forklift load.
- Door and loading-bay positions — following how lorries enter and turn.
- Ventilation and daylight — translucent sheets, roof ventilators, louvres. A hot building costs productivity and power for its whole life.
- Room to extend, where output is expected to grow.
5. Construction sequence
- Site levelling and foundations, with piling where the ground is weak.
- The floor slab — see below.
- Steel frame erection. Fabricated off site, so this stage is quick when the drawings are right.
- Roof and wall cladding.
- Services: power, water, compressed air, dust extraction, fire protection.
- Internal offices, washrooms, canteen.
- Yards, internal roads, fencing.
- Inspection and handover, including fire-safety acceptance.
The floor slab: the most underrated package
The floor carries load every day for the life of the building, and is the hardest element to repair, because repairing it means stopping production.
Where corners get cut:
- Inadequate compaction before the pour — uneven settlement a few years later.
- Movement joints not cut at the right time or the right spacing — the concrete then cracks along its own lines, randomly and visibly.
- Thickness and reinforcement not designed for the real load. A floor carrying laden forklifts is not a floor for foot traffic.
- The wrong surface finish — power float, dry shake hardener or epoxy, chosen according to chemical exposure, dust control and cleaning requirements.
Four places budgets overrun
| Overrun | How to avoid it |
|---|---|
| More piling than assumed | Investigate the ground before quoting; state the length included |
| Electrical capacity upgrade | Check the substation before buying the land |
| Rework for fire-safety approval | Bring fire design in from the start |
| Filling and ground treatment | Survey existing levels and calculate real volumes |
If the factory is built to let
The objective changes: not optimising for one process, but suiting a range of future tenants.
- Choose a conventional span and clear height so several industries can use it.
- Allow division into units with separate entrances and separately metered services.
- Design the floor above the minimum load — upgrading a slab later is effectively impossible.
- Provide spare electrical capacity.
How Tropicity builds factories
We design and build factories as a single package, including the internal offices — the element many industrial contractors treat casually because it is not their trade. Tropicity has its own joinery workshop and its own aluminium-glass workshop, so the offices, doors and partitions come from the same company as the frame.
See factory construction, the Namtex factory offices, or what a main contractor is.